Difficulty
Difficult
Steps
12
Time Required
30 - 35 minutes
Sections
3
- Back Panel
- 3 steps
- LCD Screen
- 2 steps
- Lens
- 7 steps
Flags
0
BackSony Cyber-Shot DSC-H1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Power down the camera and remove the batteries.
Power down the camera and remove the batteries.
1024
Step 2
- Using a Phillips #0 screwdriver, remove all of the screws from the back panel casing.
- There are six 5.22mm long, 3.00mm head diameter screws total.
- The left side is not shown but there should be 1 screw on that side.
Using a Phillips #0 screwdriver, remove all of the screws from the back panel casing.
There are six 5.22mm long, 3.00mm head diameter screws total.
The left side is not shown but there should be 1 screw on that side.
Step 3
- Remove the back casing.
- The casing itself is sturdy so don’t be afraid to remove it forcefully.
Remove the back casing.
The casing itself is sturdy so don’t be afraid to remove it forcefully.
Step 4
LCD Screen
- Take a hold of the right side of the LCD screen and lift it towards the left.
- The screen is held firm and will require a bit of force to ease it from its housing.
Take a hold of the right side of the LCD screen and lift it towards the left.
The screen is held firm and will require a bit of force to ease it from its housing.
Step 5
- Unplug the large conductive tape attached to the screen.
- Remove the LCD from the device.
Unplug the large conductive tape attached to the screen.
Remove the LCD from the device.
Step 6
Lens
- Unscrew and remove the gray backing behind the LCD screen.
Unscrew and remove the gray backing behind the LCD screen.
Step 7
- Using a Phillips #0 screwdriver, unscrew the four 4.24 mm black screws off the blue panel on the right side.
- Disconnect the white conductive tape.
- Remove the blue panel.
- Use tweezers to remove the three conductive tape strips on the right side.
Using a Phillips #0 screwdriver, unscrew the four 4.24 mm black screws off the blue panel on the right side.
Disconnect the white conductive tape.
Remove the blue panel.
Use tweezers to remove the three conductive tape strips on the right side.
Step 8
- Use tweezers to remove the orange conductive tape located below the shutter.
- Unplug the three ZIF connectors from the motherboard.
Use tweezers to remove the orange conductive tape located below the shutter.
Unplug the three ZIF connectors from the motherboard.
Step 9
- Flip up the blue overlapping board at the top.
- Use tweezers to disconnect the remaining connectors.
Flip up the blue overlapping board at the top.
Use tweezers to disconnect the remaining connectors.
Step 10
- Remove the motherboard and battery pack unit.
Remove the motherboard and battery pack unit.
Step 11
- Use a screwdriver to remove 5 screws on plastic panel.
- Remove the single screw on the silver panel in the center.
Use a screwdriver to remove 5 screws on plastic panel.
Remove the single screw on the silver panel in the center.
Step 12
- Use tweezers to remove the blue control panel.
- Remove the lens from the camera.
Use tweezers to remove the blue control panel.
Remove the lens from the camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Charlie Pugeda
Member since: 03/19/2018
505 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
Baylor, Team S5-G4, Williams Spring 2018
Member of Baylor, Team S5-G4, Williams Spring 2018
BU-WILLIAMS-S18S5G4
3 Members
10 Guides authored
