Difficulty
Difficult
Steps
12
Time Required
25 minutes
Sections
2
- LCD Screen
- 9 steps
- Motherboard
- 3 steps
Flags
1
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackSony Cyber-shot DSC-H200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
LCD Screen
- Using a screwdriver, remove the five 6mm screws located on the back panel.
- Using a screwdriver, remove the two 3mm screws located on the back panel.
Using a screwdriver, remove the five 6mm screws located on the back panel.
Using a screwdriver, remove the two 3mm screws located on the back panel.
1024
Step 2
- Using a screwdriver, remove one 6mm screw on the front panel.
- Using a screwdriver, remove two 3mm screws on the front panel.
Using a screwdriver, remove one 6mm screw on the front panel.
Using a screwdriver, remove two 3mm screws on the front panel.
Step 3
- Open the SD Door, unscrew and remove the single 6mm screw closest to “PUSH IN/OUT” under the SD card slot.
Open the SD Door, unscrew and remove the single 6mm screw closest to “PUSH IN/OUT” under the SD card slot.
Step 4
- Remove the back panel (the LCD and motherboard are exposed).
Remove the back panel (the LCD and motherboard are exposed).
Step 5
- Using a screwdriver, remove the three 4mm screws that attach the LCD to the camera motherboard. (The LCD is contained in a holding plate, attached to the motherboard with a ribbon cable.)
Using a screwdriver, remove the three 4mm screws that attach the LCD to the camera motherboard. (The LCD is contained in a holding plate, attached to the motherboard with a ribbon cable.)
Step 6
- Using a screwdriver, remove the single 4mm screw at the bottom of the holding plate.
Using a screwdriver, remove the single 4mm screw at the bottom of the holding plate.
Step 7
- Lift the holding plate away from the motherboard and set aside.
Lift the holding plate away from the motherboard and set aside.
Step 8
- Using tweezers, open the LCD ribbon port by lifting the black hinge. (The LCD ribbon cable will detach.)
Using tweezers, open the LCD ribbon port by lifting the black hinge. (The LCD ribbon cable will detach.)
Step 9
- Using tweezers, remove the LCD with the ribbon cable and set aside.
Using tweezers, remove the LCD with the ribbon cable and set aside.
Step 10
Motherboard
- Disconnect the four amber-colored ribbon cables from the motherboard using tweezers.
Disconnect the four amber-colored ribbon cables from the motherboard using tweezers.
Step 11
- Disconnect all wires from the motherboard by using a soldering iron.
- Users unfamiliar with a soldering iron should be extremely careful as the device can get very hot.
Disconnect all wires from the motherboard by using a soldering iron.
Users unfamiliar with a soldering iron should be extremely careful as the device can get very hot.
Step 12
- Gently lift the motherboard away from the camera body.
Gently lift the motherboard away from the camera body.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 6 other contributors
Faith Masiello
Member since: 04/08/2015
165 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
Eastern Washington University, Team 2-3, Matresse Spring 2015
Member of Eastern Washington University, Team 2-3, Matresse Spring 2015
EWU-MATRESSE-S15S2G3
4 Members
10 Guides authored
