Sony Cyber Shot Dsc H200 Tripod Port Replacement Repair Guide

Difficulty

Moderate

Steps

15

Time Required

                          30 minutes            

Sections

3

• LCD Screen
• 9 steps
• Motherboard
• 3 steps
• Tripod Port
• 3 steps

Flags

1

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

• BackSony Cyber-shot DSC-H200

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              LCD Screen               

• Using a screwdriver, remove the five 6mm screws located on the back panel.
• Using a screwdriver, remove the two 3mm screws located on the back panel.

Using a screwdriver, remove the five 6mm screws located on the back panel.

Using a screwdriver, remove the two 3mm screws located on the back panel.

1024

Step 2

• Using a screwdriver, remove one 6mm screw on the front panel.
• Using a screwdriver, remove two 3mm screws on the front panel.

Using a screwdriver, remove one 6mm screw on the front panel.

Using a screwdriver, remove two 3mm screws on the front panel.

Step 3

• Open the SD Door, unscrew and remove the single 6mm screw closest to “PUSH IN/OUT” under the SD card slot.

Open the SD Door, unscrew and remove the single 6mm screw closest to “PUSH IN/OUT” under the SD card slot.

Step 4

• Remove the back panel (the LCD and motherboard are exposed).

Remove the back panel (the LCD and motherboard are exposed).

Step 5

• Using a screwdriver, remove the three 4mm screws that attach the LCD to the camera motherboard. (The LCD is contained in a holding plate, attached to the motherboard with a ribbon cable.)

Using a screwdriver, remove the three 4mm screws that attach the LCD to the camera motherboard. (The LCD is contained in a holding plate, attached to the motherboard with a ribbon cable.)

Step 6

• Using a screwdriver, remove the single 4mm screw at the bottom of the holding plate.

Using a screwdriver, remove the single 4mm screw at the bottom of the holding plate.

Step 7

• Lift the holding plate away from the motherboard and set aside.

Lift the holding plate away from the motherboard and set aside.

Step 8

• Using tweezers, open the LCD ribbon port by lifting the black hinge. (The LCD ribbon cable will detach.)

Using tweezers, open the LCD ribbon port by lifting the black hinge. (The LCD ribbon cable will detach.)

Step 9

• Using tweezers, remove the LCD with the ribbon cable and set aside.

Using tweezers, remove the LCD with the ribbon cable and set aside.

Step 10

              Motherboard               

• Disconnect the four amber-colored ribbon cables from the motherboard using tweezers.

Disconnect the four amber-colored ribbon cables from the motherboard using tweezers.

Step 11

• Disconnect all wires from the motherboard by using a soldering iron.
• Users unfamiliar with a soldering iron should be extremely careful as the device can get very hot.

Disconnect all wires from the motherboard by using a soldering iron.

Users unfamiliar with a soldering iron should be extremely careful as the device can get very hot.

Step 12

• Gently lift the motherboard away from the camera body.

Gently lift the motherboard away from the camera body.

Step 13

              Tripod Port               

• Using a screwdriver, remove the four 4mm screws from the motherboard.
• Then remove the single 4mm screw connecting the motherboard to the main body of the camera.

Using a screwdriver, remove the four 4mm screws from the motherboard.

Then remove the single 4mm screw connecting the motherboard to the main body of the camera.

Step 14

• Lift the motherboard away from the camera body (the tripod port is exposed)

Lift the motherboard away from the camera body (the tripod port is exposed)

Step 15

• Using tweezers, lift the tripod port up and away from the camera body

Using tweezers, lift the tripod port up and away from the camera body

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 

                    Chantilly Higbee                     

Member since: 04/08/2015

152 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Eastern Washington University, Team 2-3, Matresse Spring 2015                        

                                                  Member of Eastern Washington University, Team 2-3, Matresse Spring 2015 



                    EWU-MATRESSE-S15S2G3                     


                                            4 Members                     


                                            10 Guides authored