Difficulty

Moderate

Steps

14

Time Required

                          10 - 20 minutes

Sections

1

  • LCD Screen
  • 14 steps

Flags

2

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

  • BackSony Cyber-shot DSC-HX100V

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              LCD Screen
  • Make sure the camera is turned off.
  • Press the ON/OFF button to turn off the camera.
  • Be careful, data may be lost if the camera remains on.

Make sure the camera is turned off.

Press the ON/OFF button to turn off the camera.

Be careful, data may be lost if the camera remains on.

1024

Step 2

  • Use the Phillips screwdriver size #00 to remove the 1.59mm #00 screws.
  • Remove 2 screws on the side of the camera.
  • Remove 4 screws on the bottom of the camera.
  • Remove 1 screw next to the eyepiece.

Use the Phillips screwdriver size #00 to remove the 1.59mm #00 screws.

Remove 2 screws on the side of the camera.

Remove 4 screws on the bottom of the camera.

Remove 1 screw next to the eyepiece.

Step 3

  • Tilt the screen forward.
  • Remove the two 1.59mm #00 screws on the left with the Phillips #00 screwdriver.

Tilt the screen forward.

Remove the two 1.59mm #00 screws on the left with the Phillips #00 screwdriver.

Step 4

  • Pull the back panel of the camera upward.
  • Use the spudger to help pry open the back panel.

Pull the back panel of the camera upward.

Use the spudger to help pry open the back panel.

Step 5

  • Open the back panel to view the inside of the camera.
  • Gently pull the orange ribbon cable to separate the two parts of the camera.
  • Set the front part of the camera to the side.

Open the back panel to view the inside of the camera.

Gently pull the orange ribbon cable to separate the two parts of the camera.

Set the front part of the camera to the side.

Step 6

  • Flip the entire back panel so that the screen is facing upwards.
  • Lift the screen upwards to separate it from the back panel.
  • Place the back panel off to the side. Now we will be focusing on the screen.
  • Turn the screen so that the side with the screw is facing you.
  • Remove the 1.59mm #00 screw with the Phillips #00 screwdriver.

Flip the entire back panel so that the screen is facing upwards.

Lift the screen upwards to separate it from the back panel.

Place the back panel off to the side. Now we will be focusing on the screen.

Turn the screen so that the side with the screw is facing you.

Remove the 1.59mm #00 screw with the Phillips #00 screwdriver.

Step 7

  • Flip the screen over to view the backside.
  • Use a Phillips #00 screwdriver to remove the 1.59mm #00 screw.

Flip the screen over to view the backside.

Use a Phillips #00 screwdriver to remove the 1.59mm #00 screw.

Step 8

  • Flip the screen so that the screen is facing downwards and the orange ribbon cable is on top.
  • Lift the small, black panel to remove it from the screen.

Flip the screen so that the screen is facing downwards and the orange ribbon cable is on top.

Lift the small, black panel to remove it from the screen.

Step 9

  • Lift up the entire panel with the orange ribbon cable.
  • Behind the orange ribbon cable is a small, black panel.
  • Lift the panel upwards and remove it.

Lift up the entire panel with the orange ribbon cable.

Behind the orange ribbon cable is a small, black panel.

Lift the panel upwards and remove it.

Step 10

  • Flip the screen so that the orange ribbon cable is facing downwards.
  • Press on the sliding panel and slide it upwards to remove it.

Flip the screen so that the orange ribbon cable is facing downwards.

Press on the sliding panel and slide it upwards to remove it.

Step 11

  • Remove the frame from the screen.

Remove the frame from the screen.

Step 12

  • Lift the screen upwards to view the inside.
  • Use the Phillips screwdriver size #00 to remove the 1.59mm screw inside the green square.

Lift the screen upwards to view the inside.

Use the Phillips screwdriver size #00 to remove the 1.59mm screw inside the green square.

Step 13

  • Using a Phillips #00 screwdriver, remove the three 1.59mm #00 screws from the back panel.
  • Lift up the black panel on the backside to remove.

Using a Phillips #00 screwdriver, remove the three 1.59mm #00 screws from the back panel.

Lift up the black panel on the backside to remove.

Step 14

  • Lift the entire screen upwards.
  • Gently tug the orange ribbon cable to remove the screen from the silver panel.

Lift the entire screen upwards.

Gently tug the orange ribbon cable to remove the screen from the silver panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 4 other contributors 


                    DaQuawn

Member since: 03/05/2015

251 Reputation

                                      2 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Sam Houston State, Team 11-3, Blackburne Winter 2015                        

                                                  Member of Sam Houston State, Team 11-3, Blackburne Winter 2015 



                    SHSU-BLACKBURNE-W15S11G3                     


                                            3 Members                     


                                            8 Guides authored

Shon - May 17, 2017

Reply

I followed the steps and removed cracked LCD. upon reassemly of parts after connecting replacement LCD, I found it was very difficult to connect orange ribbon back to camera body because not enough room to work with and cable is too thin and flexible. So it is better to start from Step 7 after found out someone posted the method without detaching from camera body.

Btw, I reassembled with new LCD but camera wont turn on the LCD panel at all. Changed it back to old, only cracked screen, one but now it wont come up either. So I am stuck to know what could have gone wrong.