Sony Cyber Shot Dsc Hx300 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          30 minutes - 1 hour            

Sections

2

• Battery
• 4 steps
• LCD Screen
• 8 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

• BackSony Cyber-shot DSC-HX300

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Make sure the camera is powered off
• Turn the camera upside down. This is a view of the bottom of the camera.

Make sure the camera is powered off

Turn the camera upside down. This is a view of the bottom of the camera.

1024

Step 2

• Push battery cover away from the camera.

Push battery cover away from the camera.

Step 3

• Push the blue tab that secures the battery. The battery will then spring out.

Push the blue tab that secures the battery. The battery will then spring out.

Step 4

• Remove the battery.

Remove the battery.

Step 5

              LCD Screen               

• Working on your device while it is turned on may result in electric shock. Make sure to shut down the camera, remove the battery, and unplug your device before you begin.
• Use a Phillips head screwdriver to remove one 2 cm screw located on the inside portion of the LCD hinge.

Working on your device while it is turned on may result in electric shock. Make sure to shut down the camera, remove the battery, and unplug your device before you begin.

Use a Phillips head screwdriver to remove one 2 cm screw located on the inside portion of the LCD hinge.

Step 6

• While using a plastic opening tool, carefully remove the plastic housing that surrounds the hinge.

While using a plastic opening tool, carefully remove the plastic housing that surrounds the hinge.

Step 7

• Using a small Phillips head screwdriver, remove the (2) 2 cm screws on the back of the LCD display, as indicated in the photo.
• Turn the camera on its side to access the last remaining 2 cm Phillips head screw holding the LCD case together.

Using a small Phillips head screwdriver, remove the (2) 2 cm screws on the back of the LCD display, as indicated in the photo.

Turn the camera on its side to access the last remaining 2 cm Phillips head screw holding the LCD case together.

Step 8

• Remove the plastic cover from the back of the LCD display by simply sliding it up and off of the camera.

Remove the plastic cover from the back of the LCD display by simply sliding it up and off of the camera.

Step 9

• Using a plastic opening tool, carefully remove the plastic housing that surrounds the LCD display.

Using a plastic opening tool, carefully remove the plastic housing that surrounds the LCD display.

Step 10

• Once the plastic housing is separated, disconnect the ribbon wire located on the back of the LCD display. This can be achieved by pulling up lightly on the brown bar that locks the ribbon wire to the circuit board..
• Disconnect the remaining two ribbon wires the same way. They are located on the right, rear side of the LCD frame.

Once the plastic housing is separated, disconnect the ribbon wire located on the back of the LCD display. This can be achieved by pulling up lightly on the brown bar that locks the ribbon wire to the circuit board..

Disconnect the remaining two ribbon wires the same way. They are located on the right, rear side of the LCD frame.

Step 11

• Using a small Phillips head screwdriver, remove the last 2 cm screw that mounts the circuit board to the metal LCD display frame.

Using a small Phillips head screwdriver, remove the last 2 cm screw that mounts the circuit board to the metal LCD display frame.

Step 12

• Once the circuit board is removed the replacement parts can be installed in the reverse order.

Once the circuit board is removed the replacement parts can be installed in the reverse order.

To reassemble your device, follow these instructions in reverse order. It is important to follow the steps in this order as it may not turn on properly if the user does not follow every step.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 8 other contributors 

                    Elizabeth Surface                     

Member since: 08/26/2015

1,447 Reputation

                                      9 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges                           

Team

                       USF Tampa, Team 4-6, Meier Fall 2015                        

                                                  Member of USF Tampa, Team 4-6, Meier Fall 2015 



                    USFT-MEIER-F15S4G6                     


                                            4 Members                     


                                            14 Guides authored                     

wilmer - Jan 23, 2017

Reply

my screen is working but in negative effect, any ideas??

Abdoul Traore - Nov 30, 2021

Reply