Difficulty
Moderate
Steps
21
Time Required
35 minutes
Sections
7
- Batteries
- 2 steps
- Back Case
- 4 steps
- Front Case
- 2 steps
- Top/Side Case
- 2 steps
- Battery Terminal
- 5 steps
- Motherboard
- 4 steps
- LCD Display
- 2 steps
Flags
2
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Better Introduction
Improve this guide by completing or revising its introduction.
BackSony Cyber-Shot DSC-S90
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Batteries
- Hold down the “open"button (gray oval with arrow pointing upwards) on the battery port door.
- While holding the button downwards, slide the door upwards to unlock and open the door.
Hold down the “open"button (gray oval with arrow pointing upwards) on the battery port door.
While holding the button downwards, slide the door upwards to unlock and open the door.
1024
Step 2
- Pull open the door and allow the batteries to fall out.
Pull open the door and allow the batteries to fall out.
Step 3
Back Case
- Remove the 2mm Phillips #00 screw under the battery port door.
- Remove the 2mm Phillips #00 screw towards the right of the bottom-side of the camera.
Remove the 2mm Phillips #00 screw under the battery port door.
Remove the 2mm Phillips #00 screw towards the right of the bottom-side of the camera.
Step 4
- Remove the two 2mm Phillips #00 screws (one on each side of the camera).
Remove the two 2mm Phillips #00 screws (one on each side of the camera).
Step 5
- Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the right side and bottom of the camera with the LCD screen facing you.
Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the right side and bottom of the camera with the LCD screen facing you.
Step 6
- Pull apart the back case from the main body of the camera.
Pull apart the back case from the main body of the camera.
Step 7
Front Case
- Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the top of the camera.
Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the top of the camera.
Step 8
- Pull apart the front case from the main body of the camera.
Pull apart the front case from the main body of the camera.
Step 9
Top/Side Case
- Release all clips and latches keeping the casing in place using a spudger, opening tool, or screwdriver.
Release all clips and latches keeping the casing in place using a spudger, opening tool, or screwdriver.
Step 10
- Now the casing can be removed after all latches have been undone.
Now the casing can be removed after all latches have been undone.
Step 11
Battery Terminal
- Disconnect the ribbon cables on top of the battery terminal using a spudger or screwdriver.
Disconnect the ribbon cables on top of the battery terminal using a spudger or screwdriver.
Step 12
- Disconnect the remaining ribbon cable on the side of the camera using a spudger or screwdriver.
Disconnect the remaining ribbon cable on the side of the camera using a spudger or screwdriver.
Step 13
- Use a spudger or screwdriver to unhinge the clips. This releases the battery terminal.
Use a spudger or screwdriver to unhinge the clips. This releases the battery terminal.
Step 14
- Once the battery terminal is unclipped, pull this ribbon cable out with a spudger or screwdriver to finish freeing the battery terminal.
Once the battery terminal is unclipped, pull this ribbon cable out with a spudger or screwdriver to finish freeing the battery terminal.
Step 15
- Now the battery terminal can be separated from the main body of the camera.
Now the battery terminal can be separated from the main body of the camera.
Step 16
Motherboard
- Disconnect the three pictured ribbon cables using a spudger or screwdriver.
Disconnect the three pictured ribbon cables using a spudger or screwdriver.
Step 17
- Push the clip to the left and lift the motherboard upwards and away from the camera.
Push the clip to the left and lift the motherboard upwards and away from the camera.
Step 18
- Disconnect the two ribbon cables using a spudger or screwdriver.
Disconnect the two ribbon cables using a spudger or screwdriver.
Step 19
- Unlatch the clip and lift the motherboard upwards and away from the camera.
Unlatch the clip and lift the motherboard upwards and away from the camera.
Step 20
LCD Display
- Unlatch the two clips holding the LCD display onto the main camera housing using a spudger.
Unlatch the two clips holding the LCD display onto the main camera housing using a spudger.
Step 21
- Remove the LCD.
Remove the LCD.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Jonathan Arns
Member since: 10/28/2019
745 Reputation
8 Guides authored
Badges:
5
+2 more badges
Team
UMass Dartmouth, Team S4-G5, Saloman Fall 2019
Member of UMass Dartmouth, Team S4-G5, Saloman Fall 2019
UMASSD-SALOMAN-F19S4G5
3 Members
20 Guides authored
