Difficulty

Moderate

Steps

9

Time Required

                          10 - 15 minutes

Sections

2

  • Battery
  • 2 steps
  • CCD chip
  • 7 steps

Flags

0

  • BackSony Cyber-shot DSC-T1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Locate the cover on the bottom of the camera.
  • Slide the cover towards the back of the camera.
  • Be careful—the battery can slide out on its own.

Locate the cover on the bottom of the camera.

Slide the cover towards the back of the camera.

Be careful—the battery can slide out on its own.

1024

Step 2

  • Carefully remove the exposed battery.
  • If it is difficult to remove, flip over the camera and the battery will slide out.

Carefully remove the exposed battery.

If it is difficult to remove, flip over the camera and the battery will slide out.

Step 3

              CCD chip
  • Locate and remove the 3mm screws on the bottom and sides of the camera with a JIS size #0 screwdriver.

Locate and remove the 3mm screws on the bottom and sides of the camera with a JIS size #0 screwdriver.

Step 4

  • Pull the two halves of the camera apart.
  • Place the two halves down with the insides facing you.

Pull the two halves of the camera apart.

Place the two halves down with the insides facing you.

Step 5

  • Find the two clips holding the motherboard to the black lens box.
  • Slide the plastic opening tool in between the ribbon and the black part of the clip, then flip it up. (If difficult, your fingernail can also be used)

Find the two clips holding the motherboard to the black lens box.

Slide the plastic opening tool in between the ribbon and the black part of the clip, then flip it up. (If difficult, your fingernail can also be used)

Step 6

  • After releasing the clips, pull out the black lens box.
  • If the black lens box does not come out, go back to the previous step and make sure you released the correct clips.

After releasing the clips, pull out the black lens box.

If the black lens box does not come out, go back to the previous step and make sure you released the correct clips.

Step 7

  • Locate and unscrew the two 3mm screws on the bottom of the black lens box with the JIS #0 screwdriver.

Locate and unscrew the two 3mm screws on the bottom of the black lens box with the JIS #0 screwdriver.

Step 8

  • With the tweezers remove the black tape to detach the chip from the lens box.

With the tweezers remove the black tape to detach the chip from the lens box.

Step 9

  • Grab the chip with your thumbs and carefully pull it off.
  • The copper tab will be glued to the lens box. Be careful not to rip it.
  • The attached copper ribbons are part of the CCD chip.

Grab the chip with your thumbs and carefully pull it off.

The copper tab will be glued to the lens box. Be careful not to rip it.

The attached copper ribbons are part of the CCD chip.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 7 other contributors 


                    Rosario

Member since: 04/12/2012

48 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 7-35, Maness Spring 2012                        

                                                  Member of Cal Poly, Team 7-35, Maness Spring 2012 



                    CPSU-MANESS-S12S7G35                     


                                            4 Members                     


                                            3 Guides authored