Difficulty

Moderate

Steps

12

Time Required

                          2 minutes

Sections

5

  • Battery
  • 2 steps
  • Disassembling Sony Cyber-shot DSC-T1 Removing Front Cover
  • 2 steps
  • CCD Sensor Module
  • 2 steps
  • Motherboard Assembly
  • 3 steps
  • LCD
  • 3 steps

Flags

4

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackSony Cyber-shot DSC-T1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Locate the battery door at the bottom of the camera.
  • Press down on the door and slide it back. The door will pop open.

Locate the battery door at the bottom of the camera.

Press down on the door and slide it back. The door will pop open.

1024

Step 2

  • Remove the battery from the door that you opened in the previous step.

Remove the battery from the door that you opened in the previous step.

Step 3

              Disassembling Sony Cyber-shot DSC-T1 Removing Front Cover
  • There are two screws on the left and right sides of the camera, and two screws on the bottom.
  • Use a PH00 screwdriver and remove the six 2.9mm screws.

There are two screws on the left and right sides of the camera, and two screws on the bottom.

Use a PH00 screwdriver and remove the six 2.9mm screws.

Step 4

  • Use hands to gently pry the front casing away from the camera.

Use hands to gently pry the front casing away from the camera.

Step 5

              CCD Sensor Module
  • Use the tip of a spudger to flip up the tab on the ZIF connector securing the motherboard ribbon cable.
  • The second picture shows what these tabs look like in their open positions.

Use the tip of a spudger to flip up the tab on the ZIF connector securing the motherboard ribbon cable.

The second picture shows what these tabs look like in their open positions.

Step 6

  • Grasp the CCD Sensor Module and remove it.

Grasp the CCD Sensor Module and remove it.

Step 7

              Motherboard Assembly
  • Use tweezers to slide the white piece on the back of the back cover to the right.
  • This will dislodge the white piece, allowing you to remove it from the back cover.

Use tweezers to slide the white piece on the back of the back cover to the right.

This will dislodge the white piece, allowing you to remove it from the back cover.

Step 8

  • Use the tip of a spudger to flip up the tab on the ZIF connector securing the motherboard ribbon cable.
  • Remove the ribbon cables from these two ZIF connectors.

Remove the ribbon cables from these two ZIF connectors.

Step 9

  • Lift the motherboard assembly up and rotate it so you can easily see where the internals connect to the back cover.
  • Remove the ZIF connectors from the clamp on the left end of the top piece.
  • The motherboard assembly is now separated from the back cover.

Lift the motherboard assembly up and rotate it so you can easily see where the internals connect to the back cover.

Remove the ZIF connectors from the clamp on the left end of the top piece.

The motherboard assembly is now separated from the back cover.

Step 10

              LCD
  • Use a PH00 screwdriver to remove the 2.9 mm phillips screw on the upper left side of the case.

Use a PH00 screwdriver to remove the 2.9 mm phillips screw on the upper left side of the case.

Step 11

  • Remove the back frame from the LCD assembly.
  • Turn the LCD assembly over and gently pull the top bar off (which has the shutter and power buttons).

Remove the back frame from the LCD assembly.

Turn the LCD assembly over and gently pull the top bar off (which has the shutter and power buttons).

Step 12

  • Pull the tape off that holds the LCD to the assembly.

Pull the tape off that holds the LCD to the assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 8 other contributors 


                    iDeleted

Member since: 07/07/2010

2,101 Reputation

                                      39 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges