Difficulty
Difficult
Steps
29
Time Required
Suggest a time??
Sections
7
- Battery
- 2 steps
- Front Cover
- 4 steps
- Back Cover
- 6 steps
- LCD
- 5 steps
- CCD Module
- 4 steps
- AV Port
- 4 steps
- Motherboard
- 4 steps
Flags
0
BackSony Cyber-shot DSC-T9
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- The battery cover is located on the right side of the camera.
- Slide the cover to expose the battery.
The battery cover is located on the right side of the camera.
Slide the cover to expose the battery.
1024
Step 2
- Ensure that the battery lines up properly with the slot in the camera.
- Slide battery in.
- Slide cover closed.
- Battery not shown
Ensure that the battery lines up properly with the slot in the camera.
Slide battery in.
Slide cover closed.
Battery not shown
Step 3
Front Cover
- Remove screws from outside of camera. There are 6 screws total.
- 3 screws on underside.
- 1 screw on right side, near battery cover.
- 2 screws on left side.
Remove screws from outside of camera. There are 6 screws total.
3 screws on underside.
1 screw on right side, near battery cover.
2 screws on left side.
Step 4
- Use screwdriver to remove screws.
Use screwdriver to remove screws.
Step 5
- Gently pull the front cover off of the main camera.
- All of the inner parts of the camera are attached to the back screen.
Gently pull the front cover off of the main camera.
All of the inner parts of the camera are attached to the back screen.
Step 6
- The front cover is now removed from the camera and the internal hardware is now exposed.
The front cover is now removed from the camera and the internal hardware is now exposed.
Step 7
Back Cover
- This is the camera without the front cover.
This is the camera without the front cover.
Step 8
- Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.
Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.
Step 9
- Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.
Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.
Step 10
- Pull apart the inner hardware from the back case by prying on the left side.
Pull apart the inner hardware from the back case by prying on the left side.
Step 11
- Remove the back cover.
Remove the back cover.
Step 12
- The back cover is now removed from the internal hardware.
The back cover is now removed from the internal hardware.
Step 13
LCD
- Use the spudger to pry the LCD from the camera.
Use the spudger to pry the LCD from the camera.
Step 14
- The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.
The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.
Step 15
- Flip camera to other side.
- Use tweezers to peel off black sticker, located in middle of the motherboard.
Flip camera to other side.
Use tweezers to peel off black sticker, located in middle of the motherboard.
Step 16
- Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.
Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.
Step 17
- The LCD is now removed from the camera.
The LCD is now removed from the camera.
Step 18
CCD Module
- This is the CCD module.
This is the CCD module.
Step 19
- Use plastic opening tool pop open the two ribbons attaching to the CCD module.
- These are the two ribbons.
Use plastic opening tool pop open the two ribbons attaching to the CCD module.
These are the two ribbons.
Step 20
- Remove CCD module.
- You may have to tug on the ribbons to remove the CCD module.
Remove CCD module.
You may have to tug on the ribbons to remove the CCD module.
Step 21
- The CCD module is now removed from the camera.
The CCD module is now removed from the camera.
Step 22
AV Port
- These two screws hold in the AV port.
- Use Phillips screwdriver to remove screws.
These two screws hold in the AV port.
Use Phillips screwdriver to remove screws.
Step 23
- Remove metal screw plate.
Remove metal screw plate.
Step 24
- Use pry stick to pop off ribbon.
Use pry stick to pop off ribbon.
Step 25
- Remove AV port from camera.
Remove AV port from camera.
Step 26
Motherboard
- The battery cover is located here.
- Pull away from camera to remove.
The battery cover is located here.
Pull away from camera to remove.
Step 27
- Grip on the top and bottom.
- Pull up and out to remove motherboard and attached parts.
Grip on the top and bottom.
Pull up and out to remove motherboard and attached parts.
Step 28
- Flip motherboard parts to position shown.
- There are three ribbons still attached to the motherboard.
- Pull these three ribbons to remove remaining parts from motherboard.
Flip motherboard parts to position shown.
There are three ribbons still attached to the motherboard.
Pull these three ribbons to remove remaining parts from motherboard.
Step 29
- The motherboard is now removed from the camera.
The motherboard is now removed from the camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Stephannie Allen
Member since: 03/11/2013
231 Reputation
10 Guides authored
Badges:
10
+7 more badges
Team
Clemson, Team 13-1, Benson Spring 2013
Member of Clemson, Team 13-1, Benson Spring 2013
CLEM-BENSON-S13S13G1
4 Members
20 Guides authored
Vedrasco Victor Vasili - Apr 14, 2018
Reply
Superb,thank you very much !!!
