Difficulty
Moderate
Steps
14
Time Required
3 minutes
Sections
3
- Battery
- 4 steps
- Outer Shell
- 9 steps
- Back Casing
- 1 step
Flags
0
BackSony Cyber-Shot DSC-TX30
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Using your finger, slide the release catch to unlock the battery/memory card cover.
Using your finger, slide the release catch to unlock the battery/memory card cover.
1024
Step 2
- Open the battery/memory card door.
Open the battery/memory card door.
Step 3
- Push the battery eject lever to free the battery.
Push the battery eject lever to free the battery.
Step 4
- Remove the battery from the device.
Remove the battery from the device.
Step 5
Outer Shell
- Using a Phillips #00 screwdriver, remove one black 2 2/5mm screw that is located next to the wrist band loop.
Using a Phillips #00 screwdriver, remove one black 2 2/5mm screw that is located next to the wrist band loop.
Step 6
- Using the plastic opening tool, separate the edge-casing from the rest of the camera.
Using the plastic opening tool, separate the edge-casing from the rest of the camera.
Step 7
- Pull the edge-casing off of the camera.
Pull the edge-casing off of the camera.
Step 8
- Using a Phillips #00 screwdriver, remove one silver 3mm screw located on the front side of the camera.
- Using a Phillips #00 screwdriver, remove one silver 5 2/5mm screw located on the front side of the camera
- Using a Phillips #00 screwdriver, remove one black 2 1/2mm screw located on the front side of the camera.
Using a Phillips #00 screwdriver, remove one silver 3mm screw located on the front side of the camera.
Using a Phillips #00 screwdriver, remove one silver 5 2/5mm screw located on the front side of the camera
Using a Phillips #00 screwdriver, remove one black 2 1/2mm screw located on the front side of the camera.
Step 9
- Using a Phillips #00 screwdriver, remove one 2 1/2mm screw located near the wrist strap.
Using a Phillips #00 screwdriver, remove one 2 1/2mm screw located near the wrist strap.
Step 10
- Using a Phillips #00 screwdriver remove one black 2 2/5mm screw near the tripod slot on the bottom of the casing.
Using a Phillips #00 screwdriver remove one black 2 2/5mm screw near the tripod slot on the bottom of the casing.
Step 11
- Using a Phillips #00 screwdriver remove the two 2 2/5mm black screws from the side of the camera opposite of the wrist strap
Using a Phillips #00 screwdriver remove the two 2 2/5mm black screws from the side of the camera opposite of the wrist strap
Step 12
- Using the plastic opening tool, open the device’s outer shell.
Using the plastic opening tool, open the device’s outer shell.
Step 13
- Remove the front casing of the device.
Remove the front casing of the device.
Step 14
Back Casing
- Using the plastic opening tool, remove the back casing of the device.
Using the plastic opening tool, remove the back casing of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Kellen Fulkerson
Member since: 04/11/2017
689 Reputation
6 Guides authored
Badges:
12
+9 more badges
Team
Eastern Washington University, Team S1-G6, Crane Spring 2017
Member of Eastern Washington University, Team S1-G6, Crane Spring 2017
EWU-CRANE-S17S1G6
4 Members
12 Guides authored
